This 2 Pack Universal Fit 11×4. 00-5 Flat Free lawnmower tire comes standard with a 3. 4″ Centered Hub & 3/4″ Sintered Iron bushings. Smooth Tread. Includes adapter kit to accommodate alternative hub lengths. Check your existing tire sidewall for tire, hub, and bushing size to ensure proper replacement fit.
- Tire: 2 pack 11×4. 00-5 flat free Smooth tread – check your existing tire Sidewall for tire and bushing size to ensure proper replacement fit
- Wheel: solid Black steel, 3. 4″ Centered hub, 3/4″ Sintered iron bushings
- Universal adapter kit includes: 2 – 5/8″ Sintered iron bushings, 2 – 1/2″ Nylon Spacers, 2 – 1/4″ Nylon Spacers, 2 – steel washers
- Use: replacement for front zero-turn mower tires 11×4. 00-5. Not for highway speeds
- Low hassle solution to repair or replace your mower tires
- 300 lb load capacity
































![Outlet ❤️ Invisible Stand Magnetic Ring IPhone 14 Pro Case [Non Yellowing] [10FT Military Drop Protection] Compatible With MagSafe Shockproof Protective Sturdy Slim Cover ???? Women Men 6.1’’ 2022- Clear ????](https://www.spraygunsshop.com/wp-content/uploads/2022/12/51ZBjFKJl9L-247x247.webp)

![Cheap ???? Magnetic Clear For IPhone 14 Pro Max Case With Invisible Stand [Compatible With MagSafe] [Military Drop Protection] Never Yellowing Shockproof Protective Slim Cases 6.7’’ 2022, Crystal Clear ????](https://www.spraygunsshop.com/wp-content/uploads/2022/12/51Ee53rkUtL-247x247.webp)
Richie –
First thing I would do is determine what bore size you really need. Measure the bolt size that goes through the bearings or perhaps the sleeve if your setup uses them.Remove and toss all bushings (these are crap compared to bearings) in the kit. If you can reuse the bearings from your original rims then you are set.Even if your bore size is 1/2 inch you can still use this kit by buying 1 3/8″ x 1/2″ bearings. Use 3/4″ ID bearings instead if that is the size you need.Doing the above will guarantee no tilt slop. For side to side centering, I used a 1/2″ washer next to bearings on each side (prevent binding) then the 1/2″ nylon spacer in the kit on each side and bolted everything down. Your setup will probably vary.Maybe one day Ill replace the spacer setup with custom 1/2″ ID x 3/4″ OD x 5/8 L metal spacers for ease of install and durability.
matt –
I got a flat on my 42″ toro timecutter so came online to buy a replacement. Purchased these and installed without an issue. Go on to start mowing my lawns and noticed just how much more bumpy the ride was compared to before… hopped off the mower to try to let some air out of the tires and realized there’s no air valve. Came to findout they’re just solid rubber. The inflatable stock tires absorbed a lot of the bumps, but these are just a solid- feel every bump- kind of tire. They work, and long term will probably be better money-wise, but just know going into these that they’ll create a rougher ride.
David W. Parker –
Tires arrived in a timely manner. Very easy to install on my Husqvarna RZ4623 zero turn mower. Just jack the front up or do what I did and pick up the front and put a block under it, it works the same. Wish I could have gotten the ones with gray rims to match the back rims of my mower but they were out of stock, but color was definitely not a deal breaker for the price, besides they make spray cans of the correct color to go over the black if need be but I don’t really mind it at all myself Love the fact of no longer having to put air in my front tires everytime I mow the yard. Just make sure you grease them both well with the supplied grease zerk fittings.
GSTX –
These fit time cutter 115-2554. But I had to use 1 thin and 1 thick plastic washer plus had to add a couple of steel washers to get it right. The tires are acceptable on smooth parts of my lawn but are brutal on the rough parts. However the ball bearings make my whole mower work much better especially on turns – don’t skip the added cost of the bearings. Had difficulty removing the bushings that come installed and replacing them with the bearings especially on one of the wheels – the machining tolerances need improving.
Nick –
had to modify my zero turn a bit to use (drill tractor bracket a bit wider. and stack washers either side to take up size).cub cadet 42 inch zero turn
J. apodaca –
Haven’t had to jack with my front mower tires since I put em on. Rides a little rougher but no more flats or squishy tires. Worth the money!
Richard L. Snow –
Tires made the ride just a bit more bumpy but worth it so won’t have anymore flats.
Charles W. Perkins –
Wasn’t sure if it would be the correct size but with the spacers it is a good fit for the Ariens Edge 52″ zero turn mower.Can’t speak to the durability yet as I just put them on, but if possible I will come back and update after a few weeks during heavy mowing season.Delivery was unexpectedly quick.